如果沒有固定膠的話，原因如下：
(1)硅鋼片周邊毛刺大，疊縫間隙不符合要求。
(2)碟片有差錯，造成空片、搭頭，使鐵芯疊裝后壓不實。
(3)鐵芯片有波浪、彎曲，使疊壓后夾不緊。
(4)綁扎鐵軛和鐵芯的環氧樹脂玻璃絲帶材質不佳、工藝不當、綁扎拉力不夠及固化不成堅固整體等，均造成綁扎過松、綁箍老化以及出現故障，造成鐵芯松動。
(5)夾件緊固螺栓未擰緊，或未裝防松墊圈，運行經電磁力振動后變松，使鐵芯變松，同時引起接地銅片脫落。
(6)對于夾件緊固螺栓未擰緊或有輕微的振動噪聲，可再次用大扳手重新擰緊緊固螺栓，直至噪聲消除即可;如果噪聲未消除，需要進一步采取措施。
(7)對于有少量空片、搭頭、波浪、彎曲、損壞的硅鋼片發出噪聲，可再次擰緊緊固螺栓，或加墊紙板再擰緊，如果聲音消失便可，否則要拆開鐵芯重新挑選硅鋼片，再重新疊鐵芯壓裝。在挑選硅鋼片時，應兩片一疊的，誤插一片或三片一疊的，應一律改為兩片;要挑選厚度相同的疊片;將彎曲片、殘片及波浪嚴重的硅鋼片挑出不用;毛刺大的硅鋼片需要重新去毛刺，毛刺達到小于0.03毫米后再重新疊裝。
(8)對于環氧樹脂玻璃絲帶綁箍損壞、老化、松動等故障，一律重新進行綁扎，要求材料合格。綁扎時先用臨時鋼箍箍緊，然后綁扎達一定厚度后進行烘干固化，固化成堅硬的整體后再卸去臨時鋼箍。
聯系我們